
Sectional industrial door motor: how you read the BFT PEGASO series
A sectional industrial door motor lifts the hall door on rails, dozens of times a day. The right model is chosen after the door surface, available voltage, cycle frequency and type of manual release. A wrong choice quickly doors the reducer and stops the activity in the warehouse.
In short: the surface gives the class of 20, 25 or 45 m2, the halo gives the tension, and the damage procedure decides between chain and double cable.
Do you need help choosing?
Tell us what you need and we'll send you the offer on the same working day.
An operator chosen after the actual data of the door works quietly years in a row, with simple maintenance. Note the surface, voltage and number of cycles, then decide between the automatic command and the deadman version. Don't forget the arches, the photocells and the manual unlocking. For large doors, check the three-phase feed from the hall. Compare each sectional industrial door motor in the category Sectional automation and choose the right model for your coat.
A sectional industrial door motor lifts the door panels on the rails and takes them under the roof of the hall. His choice starts from the surface of the door, from the available voltage and from the number of cycles per day. Therefore, two doors with the same width may require completely different motors.
Category Sectional automation You find BFT and Ditec operators. Below we read the codes of the BFT PEGASO series, compare the variants and go through the pre-assembly checks.
How a sectional industrial door motor works
The operator shall normally be mounted directly on the axis of the balancing arcs. The motor rotates the axis, and the cables lift the door. The bows take most of the weight. So, a sectional industrial door motor works properly only on a well-balanced door. The absolute encoder reads the position and stops the door at the race heads.
Why Door Balance Matters
A weak bow door forces the reducer to each cycle. Over time, unwanted wear and tear occurs. Therefore, the installer checks the arcs and cables before automation. At the same time, the door must slide easily and manually, without railings.
BFT PEGASO sectional door motor: how to read code
The PEGASO codes in the category follow a logic that is easy to follow. Figures 20, 25 and 45 show the maximum area of the door, in square meters. In our list, the letter L appears in the 230 V models, and W in the 400 V models. The last two digits describe the unlocking and command mode.
- Version BCJA620L01 cover doors up to 20 m2, at 230 V, with 33 rpm and a maximum torque of 50 Nm.
- The BCJA625 series climbs to 25 m2, all at 230 V, with 24 rpm and 70 Nm, for example BCJA625L02.
- Models BCJA645, such as BCJA645W01, go up to 45 m2, 400 V, with 24 rpm and 100 Nm.
The first two classes are semi-intensive. Instead, the 45 m2 class is intended for intensive use. So, you're quickly reading what a sectional industrial door motor you're facing.
Unlocking with chain or double cable
Term 01 or 11 indicates chain release and IP54 protection. Instead, term 02 or 12 indicates dual cable IP55. The chain allows manual handling of the ground door, e.g. to a power failure. The double cable decouples the engine through a simple firing. Each PEGASO model has one of these two variants. Therefore, the choice depends on who is handling the door in special situations.
Sectional door motor in the deadman version
Models with the end 11 or 12 work in the deadman mode. In other words, the door only moves while the operator holds the button down. This logic appears at the doors where man sees the moving area directly. So, at the same sectional industrial door motor you find and automatic variants, and deadman variants. However, the choice between them is based on the risk assessment for each coat of arms.
24 V alternative and Ditec model
For smaller doors, BFT ARGO 24V covers up to 20 m2. The package includes LCD display control unit and self-learning, receiver, flashing light and encoder for race heads. The force reaches 550 N, and the release is done manually. That's why ARGO comes into question when you don't need an operator on the axis.
The category also contains Ditec DOD14 engine, Powered at 230 V. For door-locking, you can complete the command with the support for the sectional door in the same category. Check in the technical file whether a sectional industrial door motor requires this accessory.
How to choose a sectional industrial door motor
For any industrial door operator, start with the door data, not the model. Note the width, height and total surface. Then check what supply is next to the door: single phase 230 V or three phase 400 V. In addition, estimate how many openings the door has on a crowded day.
- The door surface shall establish the sectional motor class: 20, 25 or 45 m2.
- The voltage in the hall decides between L and W.
- The frequency of the cycles shows whether semi-intensive use reaches.
- The desired command mode chooses between automatic and deadman.
- Access in case of damage decides between chain and double cable.
For example, a 4 x 5 meter door has exactly 20 m2. When the dimensions reach the limit, discuss with the installer and next class, 25 m2. On the other hand, a ramp door with many cycles per day better matches a 400 V sectional industrial door motor of the intensive use class.
Assembly of a sectional door motor: checks
The assembly requires an authorized electrician, especially in the 400 V variants. First, the installer fixes the operator to the axle and the support. Then connect the feed and set the race heads by encoder. Finally, test the safety devices.
- The door goes up and down without abnormal noises.
- The photocells stop the movement at the obstacle.
- Manual unlocking goes easy, without special tools.
- The lamp clearly shows when the door is moving.
At the same time, any industrial door automation falls under the rules of security of work in halls and warehouses. Useful information can be found on the website Labour Inspectorate. Therefore, any sectional industrial door motor enters the maintenance plan of the building. If the coat has other types of doors, see folding door automations and Slide door automations.
Frequently Asked Questions: Sectional Industrial Door Motor
Can I mount a 400 V motor if the halo has only 230 V?
Not directly. You need a three-phase power supply or you choose a 230 V model, such as BCJA625, if the surface allows.
What does IP54 and IP55 mean for these motors?
The IP code shows how well a sectional industrial door motor resists dust and water. In the PEGASO list, the double cable variants have IP55, and the chain variants have IP54.
Does the engine also fit on the door garage at home?
PEGASO operators are targeting industrial doors. For residential garages, see the automations for the garage door sectional.
What do they do if the door locks to half?
Stop ordering and use manual unlocking. Then call the assembler to check the arcs and set the encoder.
Compare all models in Sectional automation. The Automatizări Store Team helps you choose a sectional industrial door motor according to your coat.



















